How to connect LED strip lights together? [Expert Answer]

In no event cannot be destroyed, there are simple guidelines for linking LED strip lights. Otherwise, stability would not be assured.

In general, the nature of the LEDs and power supply may cause certain products to fail. Furthermore, an inaccurate relation is also not healthy. Three fundamental laws must be followed in this regard: 

1. Technological conformity 
2. Heat dissipation Needed 
3. The right choice of energy supplies.

LED cords with lengths of five meters or more will usually be offered for sale. Furthermore, if many tapes are required, one significant rule from the connection should be recalled, namely, that the first alternative is to link the power supply unit parallel with the LED tape. 

But what about a 10-15 meter or higher tape cassette? It seems that only the end of the first section can be connected to the first portion of the second, watching the pole and tricks. What was simpler to do? It is forbidden to do so. The bottom line is that five meters are not just calculated – this is the limit of current carry-over ice tracks.

It just fails due to too much load for a much longer length. Furthermore, the illumination is uneven – at first, the LED shines up, but the nearer the end, the darker and dimmer it will. Therefore, only parallel connection type. 

In basic terms, it is not only possible to link the LED strip lights on one side, but on both sides. This measure decreases the strain on the road considerably. The LED light is also universally illuminated. This refers in particular to high-powered tapes (above 9.0 W/m). And practitioners engaged with the installation of LED goods are encouraged to use two-way links for several years.

Much like that, there is a significant downside – additional wires have to go down the whole strip to link an LED strip to the power supply. 

Furthermore, lighting conditions also determine what sort of circuits should be used, but if chosen, a circuit with the control circuit is the safest way to operate high-power LEDs. The new LED tends to be persistent. Circuit operation lets supply any LED with the same current. This ensures that each LED in the circuit is given the same luminosity and would no longer allow for a single LED.

*** Refer to more article: https://www.instructables.com/Intro-to-LED-Strips/

The LED strip can be intensively heated during service, influencing the elements themselves adversely. Too hot, it loses its shine and crumbles inevitably. The goods should then be added to the radiator profile of the aluminum, like a decent radiator. 

Tape, which can run peacefully for five to ten years, fails for a short period without a basic proper cooling device.

The inclusion of an aluminum profile is a precondition for using the backlight of the LED. Interesting exceptions, however, are also available – SMD 3528 tape. Its strength is not more than 4, 8 W per 1 m. The LED tape can therefore be attached without the need for a heatsink to the 12V power supply. 

*** Refer to more useful article: https://www.sciencedirect.com/topics/engineering/thermal-dispersion

Only when you use a decent converter, since the voltage at which the LED is built is from 2.5 and 5 volts, the tape output is assured. The full-band voltage should be 12 or 24 V.

Simultaneously, the power distribution unit should be 30% higher than the tape itself.

The total backlight efficiency is only assured in this situation. If the converter is mounted sufficiently closely, it can run at maximum capacity called a limitation unit.

This mode of service impacts uptime adversely. Therefore, certain should be taken care of.  It would be a smart option to link the LED band to the power supply of the Jazzway among several adapters.

At the input, the voltage is alternating by 220 volts, and at the output 24 V. The output is 60 W and the output is 81 percent. 

The converter has also a safety system: from humidity according to IP20, overload, overheating, and increased power. There are airflow slots on all work surfaces.

Furthermore, the output voltage should be controlled such that this power supply can connect some sort of LED strip.

*** Refer to more article: https://www.digikey.com/en/articles/how-to-choose-the-right-power-supply-for-your-led-lighting-project

It is very easy to diagram how to connect the LED strip to this power supply. A small cord may also be connected to the outside end of the band to make it easier to bind.

You ought then to sell it yourself. It is advised that you take a wire with cables in various isolating colors (normally black – stainless steel, red + +) and weigh them from the band to the power source in an appropriate range. Then you should clean the cores on both sides.

You need to tune the ends of the cables using rosin and tin, which are then sold onto the contacts on the tape track.

In that case, a low-power soldering iron is worth using and in a limited amount of time, the operation itself can be finished. The soldering site of the heat shrinking tube should be shielded. 

It is safer to use NShVI (isolated battery bushing) or some other system for better communication consistency on the two ends of the wire when the LED strip is attached directly to the power supply. The circuit is up and going.

As we all know, only small-length LED tapes of no longer than 5 meters are available for sale. Cutting into smaller bits is not a concern because, for example, it often takes eight meters for long lighting.

In this case, the rules previously checked two segments (five and three meters) are related exclusively in parallel.

This method is done in the same way as above, except it needs more wires with a little variation.

The fact that you have to supply several LED strips can be seen in various circumstances.

Simultaneously the illumination of the shop facade or the lighting of the paints on various distances requires this scheme for connecting the LED strip with the power supply. 

The lead to the power supply from each component can be extended in this situation. It is too confusing, though, and this is an unsuitable solution. The use of a primary highway is much simpler. The LED is much easier to use on a major highway.

And you can directly run wires from the main station after connecting all areas of the backlight to electricity.

The majority is equipped for connecting LED strip lights with a 12 volt supply, a rear light of 5. 24 or more volts will occasionally be experienced.

It is certainly not worth linking such tapes directly to a common electricity network. Any diode and resistor only burn out in less than a second. 

You can concurrently connect the Ecola LED strip without electricity. It should be treated as a genuine breakthrough of this maker in the field of LED lighting.

Different LEDs can be identified per meter: 60, 72, 108,120 at the same time.

You need 24 parts of equal length LED bands, irrespective of form and color, to render such a concept in reality. And the best part, they’re just tied to the chain.

In this case, the segments are related as follows: the negative interaction of the first band with the positive contact of the second band is connected with the short wires.

Moreover, the string hits the plus point of the third, from the lower point of the second paragraph. 

Any of the other tapes have the same relation. In the end, a long LED string is obtained, which can accommodate a voltage of 288 volts, rather than parallel segment attachment.

However, you must first load and reduce the voltage to link a 220V LED band without a power source.

After all, the LED light requires a constant power source, in a standard socket, it can be interchanged. 

The key structural distinction between these strips is that the LEDs are clustered not in three groups, but 60. The diode bridge is included so that no self-assembly is necessary.

Finally, judging your strengths and skills can be worthwhile, rather than buying a ready-made option, it’s easier for you to do everything.